Flexo Plate Processing Equipment - at it´s best.

These are the units we currently have for sale.
It is possible to check the units Codes 1181,1282,12053 and 1182 as they are still in processing mode.
Some units are not the youngest, but were not used much and were carefully operated.
The reason for closing the production is the price war in Germany for photopolymer printing plates as well as the owner has a nother company in the building and needs space for expanding.
The shown prices are net prices. You need to add crating and shipping costs. Your commission will be determinde relative to the scope of order.
Please come back with any further questions you might have. But please add your complete address.
If you have found equipment which matches your customers need, we will provide you then with a detailed quotation.

Kind regards,
Reiner

The lnterFlex Washout Unit has an unique flat washer design, where plates are transported horizontally. In order to simplify plate feeding, the transport sticky plate is equipped with a clamp free, transport system. This feature will allow your company to maximize the complete plate format without wasting thousands of square cm of expensive material used for the punch bar. Simply place any plate onto the transport plate, equipped with an adhesive mat. sticky plate) Multiple plates can be placed to the adhesive plate without waisting material. Smal long stripes are often ripped of in systems with punched plates on pin bars. The fully automatic access door will close and the transport plate will invert to carry the plates upside down over the brushes and initialize washout cycle. During the washout cycle, multiple counter rotating brushes operate simultaneously. The brushes carry the solvent up to the plate while the transport plate jogs laterally and horizontally. The washed out platen is continuously in contact with the brushes. The plate is gradually lowered to the desired relief preventing detrimental pressure that can cause the loss of isolated dots. The lnterFlex Washout unit is delicate to the plate but quick and efficient with extremely low solvent consumption. Upon completion of the washout cycle, the plate proceeds through a clean solvent rinse and dry brush station. One brush carries clean solvent up to the plate and the second brush makes the plate touch dry. Next, a highly efficient exhaust system quickly removes any residual solvent fumes generated from the washout cycle in just a few seconds. An additional floor exhaust system is engaged to prevent undesirable fumes from the washout solvent from entering the plate room as the automatic door opens. Finally, the finished plate can be removed from the transport plate easily. Due to this unique patented design, the lnterFlex Washout unit provides the fastest and most optimal washout available. The use of costly lint-free towels is no longer necessary because the plate exits the lnterFlex Washout Unit dry to the touch. The entire process is incredibly quick. A .067? plate can be completely processed in 3 to 6 minutes, depending on the solvent being used and relief desired. .

 

Flat Mounting Table

1 Step is on the computer. Get the image of the complete corrugated board with all images. Place over a layer (you will get the layer with the unit) which shows the same letter/numbers as the Flat Mounter Table.
Insert the cross marks on the image which meets best the corresponding letter/number.

2 step           Producing the plates.

3 step           Punching of the cross marks by means of the special punch.

4 step           Insert the needed pins to the corresponding holes.

5 step           Put double adhesive tape on the plates, as usual

6 step           Pin the plates face down to the corresponding pins.

7 step           Roll over the milar to cover all single plates.

8 step           Cut of the letter/numbers

Done. Very simple to use, very precise and material saving.

RENZMANN ROTO 140 distiller,

stainless steel -
ready for continuous distilling.

The RENZMANN distillation units type ROTO recover contaminated solvents through continuously distillation.
A rotating scraper system permanently cleans the heat transfer surfaces; thus it is possible to distil even highly contaminated solvents or waste inks, to reduce the residue to a large extent, and to discharge it automatically.


Filling capacity: approx. 140 l
Vessel capacity: approx. 300 l

Distillation output: approx. 30-60 l/h (depending on the solvent values may differ)

Electric heating: 9 kW

BASF Cutting Table
Cutting length 1300 mm

Letterpress Exposure